Skip to content
Home Troubleshooting Problems During a Workout

Problems During a Workout

6 articles

No Power Readings

Are you new to TrainerRoad and your power isn't registering? Here's a list of the most common problems and how to fix them. Virtual Power Users VirtualPower converts speed on the trainer into power. For that to happen, we need to make sure we're getting speed readings from your device. 1. Make sure you have an ANT+ or Bluetooth Smart speed or speed/cadence sensor paired under the devices tab in the desktop software. You can get our software here: www.trainerroad.com/install 2. Make sure your speed sensor is "awake" when pairing. So make sure the back wheel is spinning when you're trying to pair. 3. Make sure you have a magnet on your rear wheel to register speed. Make sure that the magnet is close enough to the speed sensor to register. This is the number one problem. Speed sensor magnets should pass close enough to the sensor to trigger a revolution, but not so close as to touch the sensor when it passes. In other words make sure there is a small gap. Another way to check speed readings is to pair your speed/cadence sensor with another head unit like a Garmin 500. If it reads on your Garmin (while indoors) but not in TrainerRoad then please contact us at [email protected]. 4. If you're having problems pairing, make sure that the battery is semi new and that you don't have any other wireless interference. Here's some info about making sure your ANT+ is setup right. 5. Under the devices tab make sure "Power Source" is set to your trainer. VP_electron.png VP_RN1.PNG no_power_readings_1.png If you still have problems, contact us at [email protected] and we'll help you out. Power Meter Users If you have a power meter paired with TrainerRoad and you are not getting power readings then there are a couple things to check. 1. Make sure VirtualPower is not enabled. 2. Check to see if another head unit like a Garmin 500 will pick up your power readings. 3. Check your power meter battery. The older the battery, the weaker the wireless data will travel from your power meter. 4. Get your ANT+ USB stick close to your power meter. This will rule out interference and half powered batteries Still have a problem? If you still have problems, contact us at [email protected] to get things sorted out.

Device Dropouts

Sensor Battery When a device battery gets low, the reception distance decreases. Try replacing the device battery. Some devices report their battery condition over ANT+ and we display that on the Devices page. But it is not a universal feature, and speed/cadence sensors can't report it due to a protocol limitation. If your head unit picks up the signal, but TrainerRoad does not try moving your bike setup closer to your computer or phone. Sometimes a couple of feet can make a big difference. Interference Wireless devices such as 2.4 GHz routers, wireless speakers and wireless mice may interfere with the ANT+ and Bluetooth signal. ANT+ and Bluetooth use the 2.4 GHz band. Try moving any other wireless devices a couple of feet away. If you suspect your router to be interfering, you can change your wireless channel. Obstructions Is something blocking the sensor? Try removing any physical obstructions between the sensor and the ANT+/Bluetooth device Direct Line of Sight Do your best to ensure that your computer has the most direct line of sight possible to your sensors. Simply put, the closer and more level your devices are to your phone or computer, the better readings you will get. Computer battery setting Some PC's have variable battery settings. If your battery is set to "balanced", your computer may not be allocating enough power to the USB ports for the ANT+ stick or built in Bluetooth receiver to work well. Switch your power-management setting to "high performance". Still having connection issues? Email our support staff at [email protected]. We'll help you out! ANT+ Device Dropouts Here are a few things you can do to alleviate ANT+ device dropouts. Scroll down for help with Bluetooth Dropouts. Get the ANT+ USB stick closer to your devices Placing the ANT USB stick closer to your sensors will make the USB stick more likely to pick up an ANT signal. To do this, you can move your computer or iOS device closer to your sensors. If on a computer, you can also use a USB extension cable to get the USB stick closer to your devices. Software Disable Garmin ANT Agent/Express and any other software that can take over the ANT+ USB stick. Bluetooth Smart (4.0) Dropouts Interference Other wireless devices such as wireless speakers and keyboards can sometimes cause interference with your BT 4.0 devices. Try turning them off or moving them away from your setup. Still having connection issues? Email our support staff at [email protected]. We'll help you out!

Missing Workouts

Not seeing the workout that you want to ride? Let's find it. Are there filters that might be hiding them? When we added in filters, it greatly improved the way that users could find the exact workout that would work for them. But the one drawback is that some filters that were selected might limit the workouts you see if you haven't de-selected that filter. Fixing this is super quick though. First click on the workouts filters: filters_electron3.png At the bottom of the workouts filter there is a reset option. Try selecting that and see if you are able to see the workouts by going into the section where it should be. From here, you can also search within the filter to find your workout quicker. filters_electron_5.png Did it sync properly? Sometimes a ride just gets lost in the mix. To fix this, click on the workout from the Calendar tab. Then click on the three dots in the upper right corner and select Re-Sync Ride. re-sync_electron.png resync_RN1.PNG resync_RN2.PNG Missing a custom workout? If you're not seeing your custom workout in the Custom Workouts section, the app might not know that it is available. Click on the filters and reset them first. filters_electron_5.png Make sure that your workout has been published in the Workout Creator and has synced to the TrainerRoad servers so that it is ready to be used. After you publish the workout in the Workout Creator you may need to log in and out of the app and publish the workout again. MS_WC.png If you're sure that it's published but it's still not showing up, the app might not have retrieved it from the server. The quick fix for this is to refresh the workouts while in the Custom Workouts section by pressing the refresh button in the upper right hand corner of the app. custom_electron.png Still not seeing a workout? Email us at [email protected] and we'll help you find those missing workouts.