Skip to content
Home Search Results

37 results for “Pairing”

Found 37 results

How to Pair Your Devices

Here are the steps to make sure you can pair your devices to TrainerRoad: 1. Open the TrainerRoad app 2. Navigate to the "Devices" tab 3. Pedal for a few moments to wake up your devices. 4. Make sure that either Bluetooth or ANT+ is "On" 5. Once your device is visible and ready to pair, it will appear in the device list. 6. Click on the device and wait until it is highlighted green. (A green line will blink above the device tile while pairing and will become a solid green border once the device is paired.) Screen_Shot_2021-10-14_at_10.56.07_AM.png Screen_Shot_2021-10-14_at_10.56.20_AM.png Jump to the following sections below for quick tips on pairing your specific setup: - Smart Trainer - Smart Trainer + Power Meter (PowerMatch) - Mechanical Trainer + Speed Sensor (VirtualPower) - Mechanical Trainer + Power Meter How to Pair Devices on Desktop (Mac and Windows) pair_KICKRelectron.gif How to Pair Devices on Mobile (iOS and Android) pair_KICKR.gif Pairing a Smart Trainer - Ensure the trainer is plugged in and "awake" - Select the corresponding device tile on the "Devices" screen - Once your trainer is paired, a "Best Practices" screen will appear. Take note of the information shown on this screen (calibration details, firmware information, and general best practices with ERG mode). - After initially pairing your trainer, the device will automatically pair to TrainerRoad without displaying the "Best Practices" screen (but it can still be accessed in the future by selecting the trainer tile — see below for more information on accessing Device Details). - The default setting for a smart trainer is ERG mode (electronic resistance control) where TrainerRoad controls the resistance of your trainer to make sure you're hitting the power targets. - Make sure to use the TrainerRoad recommended gearing (smallest cog in the front chainring and a middle cog in the cassette) - Focus on maintaining as consistent of a cadence as possible to ensure you have the best experience. Note: if you have Bluetooth and ANT+ enabled and see two tiles corresponding to your trainer, pair to the Bluetooth version only. Pairing a Smart Trainer + Power Meter (PowerMatch) - Ensure the trainer is plugged in and "awake" - Make sure the power meter has batteries installed, and the device is awake - Select the corresponding device tiles on the "Devices" screen - Once your trainer is paired, a "Best Practices" screen will appear. Take note of the information shown on this screen (calibration details, firmware information, and general best practices with ERG mode). - Similarly, once the power meter is paired, a "Best Practices" screen will appear. Take note of the information shown on this screen (calibration details, firmware information, and tips on pedaling technique). - After initially pairing your trainer, the devices will automatically pair to TrainerRoad without displaying the "Best Practices" screens (but they can still be accessed in the future by selecting the corresponding tile — see below for more information on accessing Device Details). - The default setting for a smart trainer is ERG mode (electronic resistance control) where TrainerRoad controls the resistance of your trainer to make sure you're hitting the power targets. - There is an additional default setting when training with a smart trainer and power meter "PowerMatch." PowerMatch uses the readings from the power meter to control the resistance of your smart trainer to account for any power difference between the trainer and the power meter. Note: if you have Bluetooth and ANT+ enabled and see two tiles corresponding to your trainer, pair to the Bluetooth version only. Pairing a Non-Smart Trainer + Speed Sensor (VirtualPower) - With non-smart trainers and a speed sensor, you'll need to use a feature known as VirtualPower. VirtualPower is a power calculation that’s based on your speed readings and the unique make and model of the trainer you’re using. - To pair your speed sensor, confirm the device has batteries installed and that it's properly placed on your bike. - Wake the sensor by spinning the cranks, and select the corresponding device tile in the "Devices" screen. - If your speed sensor uses a magnet to trigger a rotation, verify the magnet is positioned to pass by the sensor arm properly. Pairing a Non-Smart Trainer + Power Meter - Make sure the power meter has batteries installed - Wake the device by spinning the cranks. - Select the corresponding device tiles in the "Devices" screen. Adjusting Device Settings From the Device Settings, you can adjust your devices' names, access mode settings, and perform calibrations. Note: Smart trainers are set to ERG Mode by default. If you have a power meter and a smart trainer, PowerMatch is enabled by default. settings_KICKRelectron.gif settings_KICKR.gif

Pairing Your Devices

USB1 vs USB2 ANT+ Sticks

If you're using TrainerRoad on a desktop or laptop computer with ANT+ devices, you probably already know that you need an ANT+ USB stick. There are two types of ANT+ USB sticks: the USB1 and USB2 stick. Depending on your computer and device setup, the type of USB stick you use can matter. Differences between USB1 and USB2 The primary difference between USB1 and USB2 is the number of ANT channels the stick supports. The number of channels determines how many devices the stick can handle, as each connected device operates on a single channel. USB1 has 4 channels (and can thus connect up to 4 devices) whereas USB2 offers 8 channels (and can thus connect up to 8 devices). USB2 not only offers the ability to pair more devices, but it also features more robust connections once devices are connected. Determining what kind of USB stick you have ANT+ USB1 sticks are no longer in production. All recently purchased ANT+ sticks will be of the USB2 variety. However, if you're using an older ANT+ stick, there's a chance it may be USB1. You can tell if your ANT+ stick is a USB1 model in two ways: 1. The stick will be labeled "USB1-Wireless USB Stick" on the reverse side of the stick. 2. If you have a Garmin-manufactured stick, the inner portion of the plug-in point will be white. If neither of the above are applicable to your ANT+ stick, it's probably USB2. Additionally, all mini ANT+ USB sticks are USB2. When do I need a USB2 ANT+ stick? The above ANT+ USB sticks are all examples of USB2 products. TrainerRoad Mac Legacy (Adobe Air) Desktop App: USB1 dongles will work with TrainerRoad Legacy (Adobe Air) on Mac Desktops unless you're trying to pair a Wahoo KICKR. You will need a USB2 dongle to use the Wahoo KICKR with the TrainerRoad Legacy desktop app. Note: if you've updated to the new Mac app, you will need to use USB2. TrainerRoad Windows and Mac Desktop App: USB1 sticks are not supported on either our Windows Desktop or new Mac Desktop software. You'll need a USB2 stick no matter what devices you're pairing. Where can I buy a USB2 ANT+ stick? TrainerRoad Recommends: Mini Garmin ANT+ Stick A great ANT+ USB stick option — and it's small enough to stay plugged in when you aren't training. Suunto Movestick Mini The Suunto Movestick Mini is another great option that's also small enough to stay plugged in. Docooler ANT+ Stick A good, more affordable option for an ANT+ USB dongle. Live in Australia? Aussie users will need to pick up an ANT+ stick from an Australian vendor or a local bike shop instead of the Amazon links above. Problems Connecting Your Devices? Visit our troubleshooting article for help getting your devices connected so you can start training!

Pairing & Connection Problems

ANT+ USB Stick Troubleshooting

If you're experiencing issues pairing your ANT+ devices to TrainerRoad, you're in the right place to get some help. This article will help you identify problems with your USB stick or your computer. These are the same steps that our support crew use when you e-mail us, so please make sure you try these steps before contacting us. If you are unsure of what you need to use ANT+ devices with TrainerRoad, you can learn all about it in the ANT+ article. Step 1: Plug the ANT+ USB Stick into Your Computer or Device This is what you will see if the ANT+ USB stick is not plugged into your computer's USB port or is not recognized. If the ANT+ stick is plugged in and still not recognized, there may be something wrong with the stick or your computer's USB port. Screen_Shot_2020-05-15_at_10.24.12_AM.png Step 2: Install Device Drivers If you're on a PC, make sure you've installed the ANT+ USB Stick and Bluetooth Drivers. For Mac users, there is no need to install these. Apple computers come with the necessary drivers already installed so you can skip this and continue to the next step. How to Check for Installed Drivers To check if the drivers are installed, go to "start" and type "Device manager". Load the program called device manager. The device might be displayed in two different locations. libusb-win32-devices Universal Serial Bus controllers Trouble installing drivers? If it looks like the drivers won't install, the next step is to try another USB Port. If that doesn't work, try installing the drivers on another computer. If you still can't install the drivers on another computer, it is likely that you have a bad ANT stick and will need a new one. If you have access to another ANT+ USB stick, try that on both computers and see if the drivers will install. It's also possible the driver was corrupted or changed by your OS or another software program. To fix this, you can uninstall your device drivers and perform a fresh install by following the instructions on this page. Drivers install on another computer, but not the one you train with? We've seen this a few times and there's not much we can do. There is likely a system-level problem keeping you from installing the drivers for the USB stick. A refresh of the operating system is often needed. This is depressing, I know. This occurs because there is a system-level problem between the operating system and Garmin's drivers for the ANT+ stick. Make sure that you test that ANT stick on more computers and USB ports on your computer before you reach this drastic level of refreshing your OS. Step 3: Check for Conflicts If the drivers are installed properly, but TrainerRoad cannot find the ANT+ USB stick, there may be conflicting programs as only one program can access the ANT+ USB stick at a time. Check for Garmin ANT Agent, or Garmin Express in the system tray. If that program is on, make sure you exit it. See screenshot examples below, or watch this video on How to Disable Garmin ANT Agent. With Garmin Express, you'll need to make sure that it's closed fully, and not running in the background, which it can default to. Check your system taskbar to ensure that it isn't running. If it is still in your taskbar, follow the images below to exit it. Garmin Express (PC) Garmin Express (Mac) Garmin ANT Agent (Mac) Make sure to select "Quit" to exit out of Garmin Express entirely. Garmin_Express_Quit_PC.png Have an Acer or other computer with Soluto installed? We've seen some pre-installed software on Acer computers (and some others) that mess with ANT+ USB sticks. If you have an Acer computer, you can manually stop these interruptive programs. 1. Go to start, then type "taskmgr". 2. Go to the process tab and look for something called "Soluto". 3. If you see that process, click on it and click "end task". 4. If that fixes the problem, you'll want to use the Soluto uninstall tool and remove it from your computer. Note: If you can't download the Soluto Uninstall Tool above by clicking it, please try right-clicking it and copying the link address to open it in a new tab. Step 4: Check if Garmin Express Can Detect the Stick If TrainerRoad can not find the stick, and there are no conflicting problems then we want to test the stick in Garmin's software to make sure it works. Open Garmin Express and locate it in the system tray (PC) or taskbar (mac), and click to open it. Make sure to close out of the Garmin Express window once done testing, and to close it from the taskbar as shown in the photos above. Working: Device is Connected and Active PC Example garmin-ant-agent-working-stick.PNG Mac Example Not Working: Device is Not Connected and Inactive PC Example garmin-ant-agent-not-working-stick.PNG Mac Example What do I do if Garmin ANT Agent/Express does not detect the ANT+ USB Stick? If the drivers are properly installed and Garmin ANT Agent/Express can't detect the stick, you'll want to repeat the process on another USB port on your computer. If you get the same result try it again on another computer. If you can't get TrainerRoad or Garmin ANT Agent/Express to detect the USB stick, you likely have a bad ANT stick and should return/exchange it from your place of purchase. Windows 11 ANT+ Drivers After updating to Windows 11, Athletes may lose the ability to pair with their ANT+ devices. This is because ANT+ drivers do not come preinstalled with Windows 11. To get ANT+ drivers on your Windows 11 PC, follow the steps below. 1. Windows Settings" ⚙️, open Updates and hit Check for updates. Note: If it already says you’re up to date, you will still need to prompt a new check. 2. In theAdvanced Options menu, click on ‘View optional update 3. Expand the list of driver updates. Locate the ANT+ driver (it shows up as Dynastream Innovations), select it, and press ‘Download and install’ to complete the process. This should get you the correct drivers. Some athletes get a notification in their notification panel asking them to finish installing the drivers. If this happens to you, confirm the installation, and you should be set! Still having problems? If you've gone through all the steps above, shoot us an email at [email protected]. To help us with the ticket, please let us know your username, your operating system, your computer brand, how the above steps went for you and what kind of ANT+ USB stick you have, details below to figure out what kind of stick you have. Don't know which type of USB stick you have? There are two kinds of ANT+ USB sticks to choose from: USB 1.0 and USB 2.0. USB 1.0 can connect up to 4 devices at a time, while USB 2.0 can handle up to 8. Most newer sticks will be 2.0 since 1.0 is no longer in production. For more information on how ANT+ works with TrainerRoad and which dongles we recommend, please visit the article on ANT+ Connectivity.

Pairing & Connection Problems

Wahoo KICKR CLIMB

The KICKR CLIMB is an indoor training device that physically adjusts the front of your bike to mimic climbing while riding indoors. TrainerRoad automatically adjusts the CLIMB based on the percent FTP of the interval your workout prescribes. The CLIMB can currently only be used with TrainerRoad while connected via Bluetooth Smart. Important Notes: The CLIMB is currently only compatible with the Wahoo KICKR (2017 Edition or newer) and Wahoo KICKR SNAP (2017 Edition or newer). The Climb will only adjust automatically when its corresponding KICKR is paired to the TrainerRoad mobile app via Bluetooth. The Climb is not compatible with the TrainerRoad desktop app or ANT+ at this time. climb_bike.jpg How does the KICKR CLIMB work with TrainerRoad? TrainerRoad automatically controls the CLIMB based on the intensity of an interval during a structured workout. Although the CLIMB is capable of simulating descending, TrainerRoad will only raise the unit to mimic climbing during training. The CLIMB automatically raises on a range from 75% to 175% of FTP. The CLIMB will automatically raise 1% with every 5% increase in FTP within the 75-175% FTP range. That means efforts at 75% of FTP, and anything below, will keep the CLIMB at 0% grade. For example, if your interval is prescribed at 80% of FTP, TrainerRoad automatically increases the grade of the CLIMB to mimic a 1% grade. Similarly, if your interval is at 100%, the grade will adjust to a 5% grade. The CLIMB maxes out at a 20% grade. This means the CLIMB won’t raise any higher than 20% once you reach 175% of your FTP. You can reference the scale below for clarity on how the grade relates to changes in % of FTP. new.png How do I set up the KICKR CLIMB with TrainerRoad? In order to use the CLIMB & KICKR/KICKR SNAP with TrainerRoad, you must first pair the CLIMB to your trainer. Once you’ve followed the steps to connect your trainer to the CLIMB, pair the KICKR/KICKR SNAP to TrainerRoad. The CLIMB will automatically adjust during your workouts once these steps are complete. Follow the links below for information on how to pair your KICKR or KICKR SNAP: How to pair the KICKR How to pair the KICKR SNAP How to Pair the CLIMB to Your Trainer Step 1: Download the Wahoo Fitness App on your iOS or Android device. If you already have the application downloaded, check the App Store or Google Play Store to confirm you’re on the latest version of the Wahoo Fitness App. Step 2: Confirm your trainer has the latest version of firmware. This step also requires the Wahoo Fitness App that you will already have downloaded from Step 1. Step 3: Confirm the CLIMB and KICKR/KICKR SNAP are plugged into a power supply. Ensure your trainer is powered by the LED lights on the rear of the trainer. Ensure the CLIMB is powered by the blue LED light illuminated on the CLIMB remote. Step 4: Press and hold the center "lock mode" button on the CLIMB remote for 3 seconds until a white LED begins to flash steadily. Step 5: Bring the CLIMB’s remote near your KICKR/KICKR SNAP until the center white LED flashes quickly, then turns solid. Success! The center white LED remaining solid indicates the CLIMB is connected and successfully paired to your trainer. Step 6: Open the Wahoo Fitness App and confirm the CLIMB is on the latest version of firmware for optimal training experience with the unit. Follow the link below for more details on how to confirm your CLIMB’s firmware is up to date: https://support.wahoofitness.com/hc/en-us/articles/360000132459 Step 7: Confirm the KICKR/KICKR SNAP and CLIMB are disconnected from the Wahoo Fitness App. Step 8: Connect the KICKR to TrainerRoad to begin training. Why is the CLIMB not automatically adjusting during my workouts? If you're still experiencing issues, shoot our support team a message at [email protected].

Trainers & Power Meters

Kurt Kinetic Trainers

Kurt Kinetic manufacture a range of indoor bike trainers which can be separated in to three distinct categories - smart trainers (known on their website as Interactive/Smart Control), mechanical trainers plus inRide power (known on their website as non-interactive/Smart), and mechanical-only (known also as ‘dumb’ trainers). Frames It is worth noticing before we delve deeper in to this, that some products with similar names fall into different categories. This is because products named 'Rock and Roll' and 'Road Machine' refer to the frame design. Now that the product has evolved, this nomenclature spans many trainer categories. Untitled_presentation__14_.png Smart ('Interactive') Trainers This category offers Smart Trainers in both frames, as well as the power unit alone (this would only be necessary if you wished to upgrade an existing frame to a smart trainer. These are known as the 'Rock and Roll Smart Control', 'Road Machine Smart Control' and the power unit alone is the 'Smart Control Power Unit' Rock and Roll Smart Control Untitled_presentation__1_.png The Kinetic Rock and Roll Smart Control is an interactive, app-controlled (ERG mode) electronic trainer that actually rocks side to side when you ride in order to closer mimic what it's like when riding outdoors. Road Machine Smart Control Untitled_presentation__2_.png The Road Machine Smart Control is a power trainer with app-controlled electronic resistance (ERG mode) and like most other indoor trainers, is locked in place and does not allow for any lateral movement (unlike the Rock and Roll, above). Smart Control Power Unit Kinetic-Smart-Control-Power-Unit.jpg The Kinetic Smart Control Power Unit installs in minutes and is the most affordable and convenient option for upgrading an existing Kinetic Rock and Roll or Road Machine trainer frame to a smart trainer. Mechanical + inRide Power Sensor Kinetic Fluid Power Bike Trainers are non-interactive (no ERG mode), however, with fluid resistance you are able to manually control the ride difficulty. Ride data is transmitted wirelessly to TrainerRoad. Kinetic Rock and Roll Untitled_presentation__12_.png The Kinetic Rock and Roll | Smart is fitted with the Kinetic inRide power sensor. The Kinetic Rock and Roll | Smart 2 is fitted with the Kinetic inRide 3 power sensor. Kinetic Road Machine Untitled_presentation__13_.png The Kinetic Road Machine | Smart is fitted with the Kinetic inRide power sensor. The Kinetic Road Machine | Smart 2 is fitted with the Kinetic inRide 3 power sensor. inRide Power Sensor The KurtKinetic inRide power sensor essentially functions a non-classic power meter. Rather than utilizing strain gauge technology, the inRide uses Virtual Power. Many Kinetic trainers come fitted with an inRide, and upgrading any Kinetic fluid trainer is simple as just installing the power sensor. Two versions of the inRide power sensor are currently available: Untitled_presentation__8_.png You can read more about pairing with the inRide here. Mechanical-only (‘dumb’ trainers) Kinetic traditional trainers are non-electronic and non-interactive. These are geared toward cyclists who cycle for fun only and are not interested in recording metrics. 'Mechanical-only' trainers are compatible with TrainerRoad when used with VirtualPower and a speed/cadence sensor. Kurt Kinetic Mechanical trainers: - Kinetic Road Machine - Kinetic Magnetic - Kinetic Z-Rollers - Cyclone Wind Trainer

Trainers & Power Meters

CycleOps Indoor Cycle 300/400

What is the CycleOps Indoor Cycle? The CycleOps Indoor Cycle is a stationary bike that has a built-in PowerTap that can connect with TrainerRoad via ANT+. TrainerRoad is compatible with the 300 and 400 series of the Indoor Cycle (only on our Legacy AIR apps). Due to the proprietary communication protocol the Indoor Cycle 300/400 uses, it will not be compatible with newer versions of the TrainerRoad application. However, it will always be available on our Legacy "AIR" application. You can download the Legacy AIR App & Adobe AIR for your operating system from the links below: - - TrainerRoad Legacy AIR App - Windows Legacy AIR App Download - Mac Legacy AIR App Download - Adobe AIR - Windows Adobe AIR [Click to Download via Harman] - Mac Adobe AIR [Click to Download via Harman] - Note: If you cannot download Adobe AIR from the links above, click the link below and download version 33.1.1.744 (which is required for the TrainerRoad Legacy AIR app to run): - Adobe AIR Download If you run into any problems installing the app, please contact [email protected], and we can help out! https://www.youtube.com/watch?v=5ZEv4eFIPtE Joule Setup From the factory, the Joule 3.0 comes set up to pair with both the power tap and the resistance unit within the Cycleops 300/400 Pro. If you wish to use the Joule 3.0 in conjunction with TrainerRoad to record your workout data, you'll need to un-pair the resistance unit from the Joule. If the resistance unit is not un-paired within the Joule, both the Joule and TrainerRoad will attempt to set the target power of the resistance unit. This will cause erratic resistance changes during a TrainerRoad workout as the Joule continuously overrides the target power set by TrainerRoad. To un-pair the resistance unit from the Joule follow these steps: 1. Press the [MODE] button until the Menu appears 2. Select the Sensors menu by highlighting it and moving the joystick to the right 3. Select the RU Sensor by scrolling down using the joystick and then moving the joystick to the right 4. Under Select Sensor, highlight the RU sensor (RuIC1) and move the joystick to the right 5. Select Delete Sensor by scrolling down using the joystick and then moving the joystick to the right. 6. At the "Are you sure?" prompt, select Yes by highlighting the text and moving the joystick to the right At this point, the Joule is set up to be used in conjunction with TrainerRoad. The resistance will no longer be controlled by the Joule, but the Joule can be used to capture data from your workouts. The resistance unit can always be re-paired to the Joule, if you wish to use the Joule with the Cycleops 400 Pro independent of TrainerRoad. Cycleops 300/400 Pro Pairing The first time that the Cycleops 400 Pro is paired to TrainerRoad it must be unplugged in order to trigger the appropriate pairing mode within the resistance unit. Steps 1 & 3 do not apply to the 300 as it does not have a resistance unit. To perform an initial pairing of the Cycleops 400 Pro with TrainerRoad, follow these steps: 1. Unplug the Cycleops 400 Pro resistance unit. cycleops1.png 2. Select the Pair Button under the Cycleops 300/400 Pro section of the TrainerRoad devices tab. cycleops2.png 3. Plug in the Cycleops 400 Pro resistance unit. cycleops3.png 4. Pedal the Cycleops 300/400 Pro. 5. The Cycleops 300/400 Pro section of the TrainerRoad devices tab turns green indicating the power tap is paired. cycleops4.png 6. Within 5 seconds, the Cycleops 300/400 Pro section of the TrainerRoad devices tab is populated with the device id of the resistance unit and power data begins to appear on the devices tab of TrainerRoad. cycleops5.png Once you've done an initial pairing with the Cycleops 300/400 Pro, and TrainerRoad has obtained the device ID, you should be able to leave the resistance unit plugged in and simply open and close the TrainerRoad application. If you un-pair the device from TrainerRoad, you must repeat the initial pairing steps above. Getting Speed to match between the Joule and TrainerRoad TrainerRoad is set up to use a wheel circumference of 2096mm with the Cycleops 300/400 Pro. In order to make the speed and distance values shown by the Joule match TrainerRoad, both must be set to a wheel circumference of 2096mm. To Set/Verify the flywheel circumference on the Joule follow these steps: 1. Press the [MODE] button until the Menu appears 2. Select the Sensors menu by highlighting it and moving the joystick to the right 3. Select the PowerIC Sensor by moving the joystick to the right 4. Under Select Sensor, highlight the PowerIC sensor (PowerIC1) and move the joystick to the right 5. Verify the circumference is set to 2096 mm. If the circumference is not set to 2096 mm, change the value to 2096 mm using the joystick. To Set/Verify the flywheel circumference in TrainerRoad follow these steps: 1. Select the Profile button on the TrainerRoad application 2. Update the Wheel Circumference to be 2096 mm cycleops6.png

Trainers & Power Meters

TrainerRoad Legacy Apps

There are two old versions of the TrainerRoad App that are available for download and use. - The Legacy App - The Legacy AIR App The Legacy version required will depend on your trainer and operating system. Below is a breakdown of the factors that will determine which app's right for your setup. Setups that Require the Legacy App - Operating System - Windows 7. - macOS X v10.10 Yosemite or earlier. - Trainer - CompuTrainer - CycleOps Powerbeam Pro If you need the Legacy App, scroll down the section: What is the TrainerRoad Legacy App? Setups that Require the Legacy AIR App - Operating System - Athlete's using CompuTrainers on macOS 10.15 Catalina or greater. - Trainer - CycleOps Indoor Cycle 300/400 If you need the Legacy AIR App, scroll down the section: What is the TrainerRoad Legacy AIR App? What is the TrainerRoad Legacy App? The TrainerRoad Legacy app is an older version of the TrainerRoad app. - It is only available for Desktop. There is no Legacy app for iOS or Android. - It is a locked version of the TrainerRoad app. No updates are made to the app. - It does not allow you to modify the Calendar, but the Calendar is viewable from within the app. - It does not include all the same features of the latest app (You can still access many of these features on the TrainerRoad website though!) - It does not support Native Bluetooth on Windows. Therefore, pairing devices in Windows via Bluetooth requires a Bluegiga BLED 112 Bluetooth dongle. Screenshot 2026-07-16 at 3.02.11 PM.png The TrainerRoad Legacy App on Mac Setups That Support the Legacy App If you need to download the Legacy App because your trainer is not compatible with the latest TrainerRoad app, you'll need to ensure your operating system supports the Legacy App. Check out the requirements below. Windows - Microsoft® Windows 7, 8, 10, or 11. - To pair devices to the app, athletes require either: - An ANT+ USB Dongle, or; - A Bluegiga BLED 112 Bluetooth dongle. - The Legacy app does not support Native Bluetooth on Windows. Mac - macOS v10.4 Mojave or earlier. - macOS v10.5 Catalina or greater cannot run the Legacy app. - Native Bluetooth is supported. - To pair devices to the app via ANT+, athletes require an ANT+ USB Dongle. How to Download and Install the Legacy App? You can download the Legacy App for your operating system from the links below: - TrainerRoad Legacy App - Windows Legacy App Download - Mac Legacy App Download If you run into any problems installing the app, please contact [email protected] and we can help out! What is the TrainerRoad Legacy AIR App? The TrainerRoad Legacy AIR app is an older version of the TrainerRoad app that runs on Adobe AIR. - It is only available for Desktop. There is no Legacy AIR app for iOS or Android. - You need to download Adobe AIR in order to run the Legacy AIR App. - It is a locked version of the TrainerRoad app. No updates are made to the app. - It does not include all the same features of the latest app (You can still access most of these features on the TrainerRoad website though!) - It does not support Native Bluetooth on Windows. Therefore, pairing devices in Windows via Bluetooth requires a Bluegiga BLED 112 Bluetooth dongle. Setups That Support the Legacy AIR App If you need to download the Legacy AIR App because your trainer is not compatible with the latest TrainerRoad app, you'll need to ensure your operating system supports the Legacy AIR App. Check out the requirements below. Windows - Microsoft® Windows 7, 8, 10, or 11. - To pair devices to the app, athletes require either: - An ANT+ USB Dongle, or; - A Bluegiga BLED 112 Bluetooth dongle. - The Legacy AIR app does not support Native Bluetooth on Windows. Mac - macOS v12 Monterey or earlier. - Native Bluetooth is supported. - To pair devices to the app via ANT+ athletes require an ANT+ USB Dongle. How to Download and Install the Legacy AIR App? You can download the Legacy AIR App & Adobe AIR for your operating system from the links below: - TrainerRoad Legacy AIR App - Windows Legacy AIR App Download - Mac Legacy AIR App Download - Adobe AIR - Windows Adobe AIR [Click to Download via Harman] - Mac Adobe AIR [Click to Download via Harman] - Note: If you cannot download Adobe AIR from the links above, click the link below and download version 33.1.1.744 (which is required for the TrainerRoad Legacy AIR app to run): - Adobe AIR Download If you run into any problems installing the app, please contact [email protected], and we can help out!

Getting Started

CycleOps Powerbeam Pro

The Powerbeam Pro is an electronic trainer that comes in either an ANT+ version or Bluetooth version. - Bluetooth Powerbeam Pro - ANT+ Powerbeam Pro 9480__2.jpg Bluetooth Powerbeam Pro The Bluetooth Powerbeam Pro pairs like any other Bluetooth device; however, it is only fully compatible via ERG mode with our Legacy desktop apps. The Powerbeam Pro is only supported as a power meter (no ERG mode) in our mobile apps. Here are links to download the TrainerRoad Legacy app. - TrainerRoad Legacy (Mac) - TrainerRoad Legacy (Windows) How to pair Powerbeam Pro via Bluetooth 1. Open the TrainerRoad App 2. Go to the Devices section of the app - Ensure that Bluetooth is On by checking the upper right-hand corner to make sure Bluetooth is highlighted in green 3. The PowerBeam device card should appear in the Devices section 4. Tap/click on your trainer to start the pairing process 5. Once the Device's card is highlighted in green it is paired Note: To learn more about Bluetooth compatibility, check out this Bluetooth Troubleshooting article. ANT+ Powerbeam Pro The ANT+ PowerBeam Pro is a little bit trickier to pair due to the proprietary nature of the ANT+ protocol they use. Due to this, the PowerBeam Pro is only fully compatible with the TrainerRoad Legacy App. The ANT+ PowerBeam Pro is only supported as a power meter (no ERG control) in our mobile apps. Here are links to download the TrainerRoad Legacy app: - TrainerRoad Legacy (Mac) - TrainerRoad Legacy (Windows) Note: For Mac, the ANT+ Powerbeam Pro is only fully supported on our Legacy AIR app. Click here for installation and setup steps. Connecting the Powerbeam Pro with the Legacy Application 1. Open the TrainerRoad App 2. Go to the Devices section of the app 3. Plug in your ANT+ stick - make sure it displays ANT+ as On in the upper right corner of the screen 4. Click Device Troubleshooting at the bottom 5. Click Search next to the PowerBeamPro 6. Click Pair when the PowerBeamPro is discovered - PowerBeam Pro should show up Green in your Devices Tab, signifying that it has successfully paired. How to pair to Legacy AIR App https://www.youtube.com/watch?v=5ZEv4eFIPtE Step 1. Open the TrainerRoad Legacy AIR app. If you do not already have this version of the app, you can download it here: - TrainerRoad Legacy (Mac) - TrainerRoad Legacy (Windows) You will want to make sure to download the latest version of Adobe Air before you start the download. - AIR download for Mac - AIR download for Windows Note: You should only download this version if you are using a PowerBeam Pro, all other users should download our latest version of the app on our Downloads Page. Step 2. Plug in your ANT+ USB stick. Step 3. Go to the Devices tab. If your screen looks like the one below after clicking the "Devices" tab, click "Search for ANT+ USB". (If you don't see this button, then good news! TrainerRoad already found your ANT+ USB stick) Step 4. Search for devices. After your ANT+ USB stick is connected, you should see the screen below. Scroll down to where you see the PowerBeam Pro listed, and click "Pair." If you have an older Power Beam Pro, clicking "Pair" may not be successful. If this is the case, you can connect with TrainerRoad by clicking "Legacy" instead of "Pair." Note: The PowerBeam Pro works best when it's paired first — before any other devices. It won't pair if you're trying to pair other devices such as heart rate monitors at the same time. Once the device is paired, it's time to do a Spindown Calibration. A Spindown Calibration aims to quantify the variable of rolling resistance (affected by tire pressure and trainer pressure) in order to get more accurate power readings. This should be done often, not just on the initial setup. Doing it every other ride, or even every ride, isn't a bad idea. After pairing the device, look for the "Spindown" button below the mode selection button. Step 1. As indicated in the window below, maintain a speed between 18-22mph for 120 seconds. Step 2. After maintaining the speed for the indicated time, stop pedaling and let your bike coast to a stop. Step 3. Once your bike has coasted to a stop, you should see the following message. Click "Done" and you're ready to ride! Troubleshooting Connection Problems? Visit our Device Pairing Troubleshooting page. ANT+ USB stick Issues? Visit our ANT+ USB Stick troubleshooting page. Spindown Calibration Problems? Have you been spinning down your PBP and TrainerRoad says something like there's 65,000 seconds left? That's actually the PBP's way of indicating that something went wrong with the spindown. This is usually due following the spindown steps incorrectly. This error can also be caused if the signal was interrupted during spindown. In order to fix this, try the following: - - Unplug your PBP for about 5 minutes and reconnect your power cord to your PBP (restart it) - Restart TrainerRoad

Trainers & Power Meters

Wahoo KICKR CORE

The Wahoo KICKR CORE is a smart trainer that connects to TrainerRoad via either ANT+ or Bluetooth Smart. TrainerRoad automatically controls the KICKR CORE's resistance in accordance with the workout's profile when the trainer is in ERG mode. How do I Set Up the KICKR CORE with TrainerRoad? Check out how to pair TrainerRoad with your Wahoo KICKR. (The KICKR and KICKR CORE have the same pairing procedure.) How Does the KICKR CORE Work with TrainerRoad? The KICKR CORE has three modes that can be used with TrainerRoad: ERG, Standard, and Resistance mode. TrainerRoad_Wahoo_Kickr_Core_11.png Why am I Unable to Calibrate my KICKR CORE using the TrainerRoad App? KICKR COREs on Firmware v1.3.17 and above will automatically calibrate on the fly as you ride. There's no need to calibrate manually with a spindown due to this functionality. You can learn more about this self-calibrating process here. ERG Mode ERG is the most commonly-used mode when performing a TrainerRoad workout with a KICKR CORE. TrainerRoad will automatically adjust the resistance on the KICKR CORE in accordance with the workout's profile in ERG mode. When using ERG mode, you can keep a steady cadence and leave your bike in a single gear for the duration of the workout. The KICKR CORE will make any necessary adjustments to the resistance. TrainerRoad_Wahoo_Kickr_Core_33.png You will be able to find the KICKR CORE's mode within a workout as the screenshot below illustrates. ERG On the Desktop app, you can toggle between modes by pressing the "M" key. Standard (Level) Mode Standard, or Level mode, mimics the functionality of a fluid trainer with variable resistance settings and non-linear, exponential power curves. In other words, as the rider increases their speed, they will encounter more resistance. You can set the KICKR CORE to varying levels of resistance (0-9) as indicated in the picture below. Core4.png This is what displays when the KICKR CORE is set to Standard mode within a workout: Core5.png Notice the Level adjuster at the bottom of the screen. You can adjust the level with the right and left arrow keys. Core6.png Resistance Mode Resistance mode mimics the functionality of a magnetic trainer with variable resistance settings and a linear power curve. This setting provides the rider with a fixed level of resistance on the flywheel that does not change as the speed is increased. You can set the KICKR CORE to varying levels of resistance (0-100) as indicated in the picture below. TrainerRoad_Wahoo_Kickr_Core_5.png This is what displays when the KICKR CORE is set to Resistance mode within a workout: TrainerRoad_Wahoo_Kickr_Core_4.png Notice the Level adjuster at the bottom of the screen. You can adjust the level with the right and left arrow keys. mceclip0.png How does the KICKR CORE work with TrainerRoad during an 8 or 20-minute FTP test? TrainerRoad will automatically switch the KICKR CORE from Erg into Standard (Level 3) mode during the test intervals (20- or 8- minute periods) of a test workout. We do this because we don't want the app to control your KICKR CORE and put limitations on how hard you can ride. TrainerRoad will control your KICKR CORE throughout the warm-up. This will ensure that you are well prepared for the test. However, once the test starts, TrainerRoad will switch modes. Level mode allows you to shift gears to find the optimal cadence for your test and will help you achieve the highest wattage average possible. What do I do if it is very difficult to pedal in Level mode? We recommend switching to Level mode before you do the test to find the level that will work for you. Use the left/right arrows on the keyboard or the slider at the bottom of the workout window to change levels. Next, you can change gears on your bike as you'd do outside to find the correct cadence.

Trainers & Power Meters

PowerMatch: Using Power Meters with Smart Trainers

PowerMatch is a feature from TrainerRoad that allows you to use a power meter to control the resistance on your smart trainer. How PowerMatch Works PowerMatch allows riders to display and record power readings from their power meter and still benefit from the automatic resistance control of their smart trainer. It lets riders get consistent power readings from their power meter both indoors and outdoors without having to give up the benefits of their smart trainer. Put simply, PowerMatch will use the power readings from your power meter to control your smart trainer. TrainerRoad will measure the power offset between your power meter and smart trainer; it will then adjust the resistance of your smart trainer based on that offset in power and the current interval target. PowerMatch will work with any smart trainer that works in ERG mode with TrainerRoad. "What is the "power offset" you're talking about?" The reality of the power-device world is that different devices will often display discrepancies in their readings. For example, an output of 200 watts on a power meter may equate to an output of 220 watts on a smart trainer. These two devices would have an offset of 20 watts at that level of output. PowerMatch effectively neutralizes this offset. Using PowerMatch with Mobile TrainerRoad's default PowerMatch setting is to use the power from the power meter to control the smart trainer's resistance. Simply pair the power meter and smart trainer, make sure PowerMatch is set to "New", and TrainerRoad will take care of the rest! Additionally, the offset between the power meter and smart trainer will be measured, and the trainer adjusted (if necessary), constantly. Note that the power meter will display as your power source in your Online Career. powermatchRN1.PNG Using PowerMatch with Desktop TrainerRoad's default PowerMatch setting is to use the power from the power meter to control the smart trainer's resistance. Simply pair the power meter and smart trainer, and TrainerRoad will take care of the rest! Additionally, the offset between the power meter and smart trainer will be measured, and the trainer adjusted (if necessary), constantly. Note that the power meter will display as your power source in your Online Career. powermatch_electron1.png If you wish to disable PowerMatch or apply a consistent offset, you may do so under the Device Settings menu, by clicking on the paired smart trainer. powermatch_electron2.png Sensitivity Setting Sensitivity is an advanced setting for our newest version of PowerMatch. It is set at 0.5 by default, which proved to be a better experience for most athletes. However, you may find that a different setting works better for your power meter / trainer combination and or personal preferences. A higher value should translate to quicker update to the trainer / power meter offset. While this may sound desirable, updating too fast can make for jumpy resistance levels. A lower sensitivity will likely result in smoother power, but the resistance adjustments from changes in power offset may take longer. How to Disable PowerMatch If you wish to disable PowerMatch, you may do so within the pairing screen of your smart trainer. Disabling PowerMatch will prompt TrainerRoad to display and record power readings from your power meter if both a power meter and smart trainer are paired at the same time. ERG mode is still available; however, the smart trainer will use its own power data to calculate resistance instead of the data from your power meter. If there is a discrepancy in power readings between the smart trainer and power meter, disabling PowerMatch can make it look like you are constantly above or below the power target. powermatchRN2.PNG Apply Consistent Offset Between Trainer/Power Meter If you know the power offset between your trainer and power meter and do not wish for TrainerRoad to continuously measure and adjust this, you can input this offset to be applied to the entire workout. You can do this within the pairing screen of your smart trainer. Note: The offset calibrates your trainer to your power meter. In other words, the manual offset adjusts your trainer to be at the same output as your power meter. For example, if your trainer reads 200 watts and your power meter reads 210 watts, you will apply a -10 watt offset. powermatchRN3.PNG Legacy PowerMatch Setting The Legacy PowerMatch setting uses our older version of PowerMatch. We've found the new version (enabled by default) improves trainer responsiveness and provides a better experience. If you preferred the earlier version, select Legacy under PowerMatch settings. Using PowerMatch with Legacy AIR App TrainerRoad's default PowerMatch setting is to use the power from the power meter to control the smart trainer's resistance. Simply pair the power meter and smart trainer, and TrainerRoad will take care of the rest! Note that the power meter will display as your power source in your Online Career. Additionally, the offset between the power meter and smart trainer will be measured and adjusted (if necessary) every ten seconds as per the default settings. If you wish to disable PowerMatch or apply a consistent offset, you may do so under your Profile tab. Disabling PowerMatch will prompt TrainerRoad to display & record power readings from the power meter if both a power meter and smart trainer are paired at the same time. According to our device paring hierarchy, the power meter will take precedence over the trainer. If you don't want to use PowerMatch, and you'd like power readings from only your smart trainer, unpair your power meter. If you know the power offset between your trainer and power meter and do not wish for TrainerRoad to continuously measure and adjust this, you can input this offset to be applied to the entire workout. Why Does My Power Appear Less Smooth with PowerMatch Applied? Those well-versed in smart trainer usage will be very familiar with the smooth nature of graphed power in ERG mode. This power appears so smooth primarily because of natural smoothing that the sizable flywheels of many smart trainers applies. Many strain-gauge power meters measure power directly from the pedal, crank arm, or crank. This method of measuring power is more sensitive than what most smart trainers use, and thus, even riders with the smoothest pedal strokes will notice "jumpier" power readings. This is nothing to worry about so long as the fluctuations are not drastic. Power Graphed with only Smart Trainer Power Graphed with PowerMatch (Smart Trainer + Power Meter) Despite these graphs appearing slightly different, both users got the same training benefit from these intervals. The top profile simply doesn't represent the actual fluctuations in power as clearly as the bottom.

Trainers & Power Meters